Automatic Paper Punching And Cutting Machine Using Geneva Mechanism


EOI: 10.11242/viva-tech.01.05.001

Download Full Text here



Citation

Shivam Nayak, Abhishek Upadhyay, Krishna Mishra, Daksha Palav, "Automatic Paper Punching And Cutting Machine Using Geneva Mechanism", VIVA-IJRI Volume 1, Issue 5, Article 48, pp. 1-7, 2022. Published by Computer Engineering Department, VIVA Institute of Technology, Virar, India.

Abstract

In this project automated paper punching and cutting machine based on Geneva mechanism. The machine cut the papers equal lengths as well as punching based on Geneva mechanism. The machine uses a 12 V motor in order to drive the entire system. A shaft was used in this machine which is directly connected to the motor and cam drive by the support(frame). This shaft has a sprocket which is connected to scissors by a chain in order to drive the cutting mechanism for cutting paper and also the cam drive is employed with slider crank mechanism which gives the motion to punching motion. Now another sprocket is connected to a Geneva mechanism wheel. This wheel was used to drive paper feed into the cutter mechanism. When the motor is run through battery and the cam drive rotates clockwise direction then punching is doing on paper as well as cutting through chain drive here punching and cutting is doing on single operation with this machine save the lot time.

Keywords

Cutting, Geneva Wheel, Motor, Punching, Sprocket.

References

  1. “Hybrid Ecopower Hybrid Ventilator ”https://skylinegroup.co.in/ecopower.html Last Accessed on 5th March, 2020.
  2. "Vidhate Pankaj, Vyavhare Sagar, Wagh Sandip, Bajaj Vaibhav, Agale Ratnadeep, Kathar Nitesh, "Design and Fabrication of Hacksaw Machine Using Scotch Yoke Mechanism ", International Journal of Advance Research and Innovative Ideas in Education (IJARIIE), Vol-3, Issue-3, PP- 2357-2362, 2017.
  3. "R. Syam Sudhakar Rao, A. Hari Tej, C. Siva Sai, A. Rupesh Kumar, A. Narayana Reddy, B. Sai Krishna, "Design of Geneva wheel Based Auto-Roll Punching Machine ", International Research Journal of Engineering and Technology (IRJET), Vol-4, Issue-3,March 2017.
  4. "Sagar R. Patil 1, Fenil Y. Mananil , Nikhil R. Mhatre 1, Abhishek P. Poojary , S. M. Gaikwad, " Design and Fabrication of Paper Cutting Machine using Geneva Mechanism ", International Journal of Innovative Research in Science, Engineering and Technology, Vol-8, Issue-4, April 2019.
  5. "Rakesh Prajapati, Purvik Patel, Saurabh Modi, “Design and Development of Machine to Perform Stamping and Cutting Operation”,International Journal of Advance Engineering and Research Development, April-2017.
  6. "Praveen Kumar, Pragatheesan K, Ramachandran M, Ramu P, Sanjay G, “Design and Fabrication of Paper Cutting Machine Using Geneva Mechanism”, IJARIE, Vol-5, Issue-2,2019.
  7. "Rutvij Shah, Parth Kadiya , Pratik Prajapati , Tishy Patel , Dhruvil Prajapati and Dr. Utsav Gadhia , “ Design of Automatic Paper Punching and Spiral Binding Machine using Geneva Cam Mechanism” , Zeichen Journal .
  8. "Sara Al Drais, Fatmah Al Zhraa Ibrahim, Nourah Al Fouderi, Ali Mamedov, “Design of an Automated Paper Cutting Machine”,proceedings of the International Conference on Industrial Engineering and Operations Management Sao Paulo Brazil, April 5-8,2021